- Fixed bugs in rules.mk for S60-X

- Updated dbroqua layout for S60-X (added backlight)

keyboards/s60-x/default/rules.mk

@@ -1 +1,9 @@
-RGBLIGHT_ENABLE ?= no
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+NKRO_ENABLE ?= no          # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= yes     # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE ?= no
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif

keyboards/s60-x/keymaps/dbroqua/keymap.c

@@ -66,7 +66,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  */
   [_SFX] = KEYMAP(
       ______,   ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \
-      ______,   ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,  \
+      ______,   BL_TOGG,BL_STEP,BL_DEC, BL_INC, ______, ______, ______, ______, ______, ______, ______, ______, ______,  \
       ______,   F(0),   F(1),   ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______,  \
       ______,   ______, F(2),   F(3),   F(4),   F(5),   F(6),   F(7),   ______, ______, ______, ______, ______, ______, ______,  \
       ______,   ______, ______,                         ______,                         ______, ______, ______, ______ \

keyboards/s60-x/rgb/config.h

@@ -9,6 +9,7 @@
 /* key matrix pins */
 #define MATRIX_ROW_PINS { B5, B4, D7, D6, D4 }
 #define MATRIX_COL_PINS { D0, D1, D2, D3, D5, B6, C6, C7, F1, F0, E6, B3, B2, B1, B0 }
+#define UNUSED_PINS
 
 /* number of backlight levels */
 #define BACKLIGHT_PIN B7
@@ -16,6 +17,12 @@
 #define BACKLIGHT_LEVELS 3
 #endif
 
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
 /* prevent stuck modifiers */
 #define PREVENT_STUCK_MODIFIERS
 

keyboards/s60-x/rgb/rules.mk

@@ -1,56 +1,9 @@
-# MCU name
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
-MCU = atmega32u4
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+NKRO_ENABLE ?= yes          # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= yes     # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE ?= yes      # Enable RGB light
 
-# Processor frequency.
+ifndef QUANTUM_DIR
-#     This will define a symbol, F_CPU, in all source code files equal to the
+	include ../../../Makefile
-#     processor frequency in Hz. You can then use this symbol in your source code to
+endif
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= no	# Console for debug(+400)
-COMMAND_ENABLE ?= no    # Commands for debug and configuration
-SLEEP_LED_ENABLE ?= no  # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality
-AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= yes

keyboards/s60-x/rules.mk

@@ -56,13 +56,9 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
 EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
 MIDI_ENABLE ?= no            # MIDI controls
 UNICODE_ENABLE ?= no         # Unicode
 BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID