* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
* Remove QUANTUM_DIR code blocks from keyboard rules
This commit removes the deprecated "QUANTUM_DIR" code block from
rules.mk files that affect entire keyboards.
* remove QUANTUM_DIR code blocks from rules for default keymaps
This commit removes the deprecated "QUANTUM_DIR" code block from
rules.mk files that affect default keymaps.
* remove QUANTUM_DIR code blocks from rules for user keymaps
This commit removes the deprecated "QUANTUM_DIR" code block from
rules.mk files that affect "user" keymaps. (It's actually any keymap
that isn't named `default`.)
* remove QUANTUM_DIR code blocks from rules for community layouts
This commit removes the deprecated "QUANTUM_DIR" code block from
rules.mk files for community layouts.
* remove QUANTUM_DIR code blocks from rules for userspaces
This commit removes the deprecated "QUANTUM_DIR" code block from
rules.mk files for userspaces.
* Implement macro recording
* Remove off-by-one from the macro recorder
* Holding both modifiers enables the third layer
* Exit the 3rd layer into one of the secondary ones
* Regular Enter and Escape on the secondary layers
Useful for the macro recording because the "tap" modifiers always act as
modifiers there.
* Remove the buffer overflow from the macro recorder
When the limit is reached, the backlight blinks with each keypress.
* More robust macro recording implementation
* Macro record refactoring and improvement
- support for a second macro (saved using the end of the macro buffer)
- improved reliability
* Add comments to my macros
* Macro recording: remove a redundant code
* Separate the raise+lower layer from the special layer
* Add back/forward keys
* Bind mouse movement
* More readable KC_TRNS
* Improve the mouse bindings
* Use a convenience macro instead of the low-level ACTION macro
* Add mouse to the Dual layer; make most of the layer transparent
* New "mouse" layer; clean up the "special" layer
* CapsLock, NumLock and ScrollLock on the Special layer
* Enable my fix for the stuck modifiers and adjust the dual layer to it
* Fix the macro recording after enabling the stuck mods fix
* Click with Lower/Raise+Space
* Reduce the memory used by the macro recording
Previously the auxiliary layers were numbered 30 and 31 which resulted
in all 32 array elements being allocated regardless of the actually
used layers in the user code.
* Optimize source_layers_cache for the cache memory
Swapping the array indices should increase the locality of the memory access.
* Remove the mouse layer
* Use update_tri_layer to simplify the code
* Add some custom per-keymap build options
* Add ShiftLock
* Secure the reset button
* Add numeric layer
* Remove explicit layer keys on LW and RS layers
* Replace Alt+left/right with Back/Forward keys
* Sleep/delay key (for macro recording)
* App/menu key
* Fix stuff after merging to master
* Local per-keymap config.h; minor cleanup
* Remove the old macro_record.h
Replaced with dynamic_macro.h
* Adjust my keymap to the current API
* Pure Pro Gaming layer
Accessible by double tapping the Pure Pro layer. It features switched
Lower and Raise layers, for one-handed access to numbers.
* Pure Pro Gaming layer: no Mod4, persistent number layer under RShift
* Pure Pro Gaming layer activated with long press, not double press
* Reduce the size of the vifon keymap
See: issue #930
* Increase the dynamic macro buffer
The default was actually decreased. The actual used value didn't change.
* Add the context menu key
* No more strange ideas in the gaming layer
* Reduce the firmware size by disabling API_SYSEX_ENABLE
* Make slash available on the PP layer (replaces the RESET key)
* Add a generic "hold this key" macro
* Add a missing undef
* Turn LGUI in the gaming layer into LW instead of disabling it
It's not as disruptive as LGUI and it makes the LW/RS order kind of
more consistent (LW on the left, RS on the right).
* Refactor the Pure Pro Gaming layer
* Try out the 1st party qmk KC_LOCK (vs my own KM_HOLD)
* Alternative way to switch keyboard layouts with the left hand
* Add dot & slash to the Pure Pro layer (but not to the Gaming layer)
* Now that there is a second KM_LW, we can simplify the layout a bit
It was confusing to have the modifiers completely swapped. Just
moving them is much more natural.
* Disable the console now that qmk got bigger
* Update the keymap for the modern qmk standards
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
* initial files for rev 6 with encoder
* music map init, dip scan added
* adds ws2812 driver for arm
* flesh out dip and encoder support
* adds default encoder res
* adds default encoder res
* start muse implementation
* muse working with encoder as control
* flip direction
* try mouse wheel again
* dont break other revs
* dont break other revs
* conditional autio
* pwm ws driver (not working)
* update build includes for chibios
* update ws2812 driver/config
* last commit for glasser code
* working example
* remove rgb for now
* finish up rev6
* working encoder keycodes
* add warnings to planck keymaps about the LAYOUT
* Remove all Makefiles from the keyboards directory.
* update keymaps added in the last 8 days
* Ignore keyboard/keymap makefiles
* update hand_wire to reflect our new Makefile-less reality
* Update the make guide to reflect the new reality
* move planck keymap options to rules.mk
* update planck keymaps 4real
* trigger travis
* add back build_keyboard.mk
* restore changes to build_keyboard
James Young
Ryan
Drashna Jaelre
Wojciech Siewierski
Joe Wasson
Jack Humbert
skullydazed
Weiyi Lou
cbbrowne