* PMW33XX drivers overhaul
This combines the PMW3389 and PM3360 drivers as they only differ in the
firmware blobs and CPI get and set functions. The following changes have
been made:
* PMW3389 now gets the same multi-sensor feature that is already available on the
PMW3360.
* Introduced a shared pmw33xx_report_t struct is now directly readable via SPI
transactions instead of individual byte-sized reads, saving multiple
copies and bitshift operations.
* pmw33(89/60)_get_report functions had unreachable branches in their motion
detection logic these have been simplied as much as possible.
* The fast firmware upload option has been removed as this becomes obsolete by
the newly introduced polled waiting functions for ChibiOS polled waiting
* PMW33(60/89)_SPI_LSBFIRST and PMW33(60/89)_SPI_MODE config options
have been removed as they don't need to be configurable.
* All PMW3389 and PMW3360 defines have been unified to a PMW33XX prefix
to reduce code duplication and make the defines interchangeable
* Adjust keyboards to PMW33XX naming scheme
* Tentative Teensy 3.5 support
* Set firmware format to .hex for ARM Teensys
* Got to "device descriptor failed" by comparing with Teensy 3.6 code
* Drop down to 96MHz...
* Bump back up to 120MHz
* Disable RESET keycode because of naming conflicts
* Add Pico SDK as submodule
* Add RP2040 build support to QMK
* Adjust USB endpoint structs for RP2040
* Add RP2040 bootloader and double-tap reset routine
* Add generic and pro micro RP2040 boards
* Add RP2040 onekey keyboard
* Add WS2812 PIO DMA enabled driver and documentation
Supports regular and open-drain output configuration. RP2040 GPIOs are
sadly not 5V tolerant, so this is a bit use-less or needs extra hardware
or you take the risk to fry your hardware.
* Adjust SIO Driver for RP2040
* Adjust I2C Driver for RP2040
* Adjust SPI Driver for RP2040
* Add PIO serial driver and documentation
* Add general RP2040 documentation
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Refactor steno into STENO_ENABLE_[ALL|GEMINI|BOLT]
* Update stenography documentation
* STENO_ENABLE_TXBOLT → STENO_ENABLE_BOLT
TXBOLT is a better name but BOLT is more consistent with the
pre-existing TX Bolt related constants, which all drop the "TX " prefix
* Comments
* STENO_ENABLE_[GEMINI|BOLT|ALL] → STENO_PROTOCOL = [geminipr|txbolt|all]
* Add note on lacking V-USB support
* Clear chord at the end of the switch(mode){send_steno_chord} block
* Return true if NOEVENT
* update_chord_xxx → add_xxx_key_to_chord
* Enable the defines for all the protocols if STENO_PROTOCOL = all
* Mention how to use `steno_set_mode`
* Set the default steno protocol to "all"
This is done so that existing keymaps invoking `steno_set_mode` don't
all suddenly break
* Add data driver equivalents for stenography feature
* Document format of serial steno packets
(Thanks dnaq)
* Add missing comma
precondition
Drashna Jael're
QMK Bot
JayceFayne
jack
Albert Y
Ben Fiedler
Stefan Kerkmann
Daniel Kao
James Young
zvecr
Ryan
CoffeeIsLife
ripdog
Osamu Aoki
FREEWING.JP
Josh Hinnebusch
Nick Brassel
ihatechoosingusernames
Thomas Kriechbaumer